Get tutorials Raspberry Pi Sensor Kit V2.0 for Raspberry Pi B+

Lesson 33 RTC DS1302

Introduction

DS1302 is a trickle charging clock chip, launched by DALLAS in America. With a built-in real-time clock/calendar and a 31-byte static RAM, it can communicate with MCU through simple serial interfaces. The real-time clock/calendar circuit provides information about second, minute, hour, day, week, month, and year. DS1302 can automatically adjust the number of days per month and days in leap year. You can determine to use a 24-hour or 12-hour system by AM/PM selection.


 

 


Components

- 1 * Raspberry Pi

- 1 * Breadboard

- 4 * Jumper wires (Male to Male, 2 red and 2 black)

- 1 * Network cable (or USB wireless network adapter)

- 1 * DS1302 RTC module

- 1 * 5-Pin anti-reverse cable

 

Experimental Principle

Interfacing the DS1302 with a microprocessor is simplified by using synchronous serial communication. Only three wires are required to communicate with the clock/RAM: RST, serial data (SDA) and serial clock (SCL). SDA can be transferred to and from the clock/RAM one byte at a time or in a burst of up to 31 bytes.


After the time of the DS1302 is set manually, the MCU starts to read the accurate time and date returned by DS1302.

 

The schematic diagram is as shown below:

 

 

Experimental Procedures

For C language users:

Step 1: Build the circuit


Raspberry Pi

T-Cobbler

RTC DS1302 Module

GPIO0

GPIO17

SCL

GPIO1

GPIO18

SDA

GPIO2

GPIO27

RST

5V

5V0

VCC

GND

GND

GND

 

 

Step 2: Change directory

cd /home/pi/SunFounder_SensorKit_for_RPi2/C/33_ds1302/

Step 3: Compile:

gcc gcc rtc_ds1302.c -lwiringPi -lwiringPiDev

Step 4: Set up time by:

sudo ./a.out –sdsc

       Set year, month, date as YYMMDD

       Set hour, minute, second as HHMMSS(24-hour clock)

       Set weekday (0 as Sunday)

Step 5: Run :

sudo sudo ./a.out


For Python users:

Step 1: Build the circuit


Raspberry Pi

T-Cobbler

RTC DS1302 Module

GPIO4

GPIO23

SCL

GPIO5

GPIO24

SDA

GPIO6

GPIO25

RST

5V

5V0

VCC

GND

GND

GND

 

 

Step 2: Change directory

 cd /home/pi/SunFounder_SensorKit_for_RPi2/Python/

Step 3: Run

sudo python 33_ds1302.py

 

Now you can see the time on the screen.

 

 

 

C Code 


#include <stdio.h>
#include <stdlib.h>
#include <stdint.h>
#include <string.h>
#include <time.h>

#include <wiringPi.h>
#include <ds1302.h>

// Register defines

#define	RTC_SECS	 0
#define	RTC_MINS	 1
#define	RTC_HOURS	 2
#define	RTC_DATE	 3
#define	RTC_MONTH	 4
#define	RTC_DAY		 5
#define	RTC_YEAR	 6
#define	RTC_WP		 7
#define	RTC_TC		 8
#define	RTC_BM		31


static unsigned int masks [] = { 0x7F, 0x7F, 0x3F, 0x3F, 0x1F, 0x07, 0xFF } ;


// bcdToD: dToBCD:
static int bcdToD (unsigned int byte, unsigned int mask)
{
  unsigned int b1, b2 ;
  byte &= mask ;
  b1 = byte & 0x0F ;
  b2 = ((byte >> 4) & 0x0F) * 10 ;
  return b1 + b2 ;
}

static unsigned int dToBcd (unsigned int byte)
{
  return ((byte / 10) << 4) + (byte % 10) ;
}

// ramTest:
static int ramTestValues [] =
  { 0x00, 0xFF, 0xAA, 0x55, 0x01, 0x02, 0x04, 0x08, 0x10, 0x20, 0x40, 0x80, 0x00, 0xF0, 0x0F, -1 } ;

static int ramTest (void)
{
  int addr ;
  int got ;
  int i = 0 ;
  int errors = 0 ;
  int testVal ;

  printf ("DS1302 RAM TEST\n") ;

  testVal = ramTestValues [i] ;

  while (testVal != -1)
  {
    for (addr = 0 ; addr < 31 ; ++addr)
      ds1302ramWrite (addr, testVal) ;

    for (addr = 0 ; addr < 31 ; ++addr)
      if ((got = ds1302ramRead (addr)) != testVal)
      {
	printf ("DS1302 RAM Failure: Address: %2d, Expected: 0x%02X, Got: 0x%02X\n",
		addr, testVal, got) ;
	++errors ;
      }
    testVal = ramTestValues [++i] ;
  }

  for (addr = 0 ; addr < 31 ; ++addr)
    ds1302ramWrite (addr, addr) ;

  for (addr = 0 ; addr < 31 ; ++addr)
    if ((got = ds1302ramRead (addr)) != addr)
    {
      printf ("DS1302 RAM Failure: Address: %2d, Expected: 0x%02X, Got: 0x%02X\n",
	      addr, addr, got) ;
      ++errors ;
    }

  if (errors == 0)
    printf ("-- DS1302 RAM TEST: OK\n") ;
  else
    printf ("-- DS1302 RAM TEST FAILURE. %d errors.\n", errors) ;

  return 0 ;
}

// setLinuxClock:
static int setLinuxClock (void)
{
  char dateTime [20] ;
  char command [64] ;
  int  clock [8] ;


  printf ("Setting the Linux Clock from the DS1302... ") ; fflush (stdout) ;

  ds1302clockRead (clock) ;

// [MMDDhhmm[[CC]YY][.ss]]

  sprintf (dateTime, "%02d%02d%02d%02d%02d%02d.%02d",
	bcdToD (clock [RTC_MONTH], masks [RTC_MONTH]),
	bcdToD (clock [RTC_DATE],  masks [RTC_DATE]),
	bcdToD (clock [RTC_HOURS], masks [RTC_HOURS]),
	bcdToD (clock [RTC_MINS],  masks [RTC_MINS]),
	20,
	bcdToD (clock [RTC_YEAR],  masks [RTC_YEAR]),
	bcdToD (clock [RTC_SECS],  masks [RTC_SECS])) ;

  sprintf (command, "/bin/date %s", dateTime) ;
  system (command) ;

  return 0 ;
}



// setDSclock:
static int setDSclock (void)
{
  struct tm t ;
  time_t now ;
  int clock [8] ;
  int time = 0 ;
  int date = 0 ;
  int weekday = 0 ;

  printf ("Setting the clock in the DS1302 from type in... ") ;

  printf ("\n\nEnter Date(YYMMDD): ") ;
  scanf ("%d", &date) ;
  printf ("Enter time(HHMMSS, 24-hour clock): ") ;
  scanf ("%d", &time) ;
  printf ("Enter Weekday(0 as sunday): ") ;
  scanf ("%d", &weekday) ;
//  printf("\ndate: %d,  time: %d\n\n", date, time) ;

  clock [ 0] = dToBcd (time % 100) ;	// seconds
  clock [ 1] = dToBcd (time / 100 % 100) ;	// mins
  clock [ 2] = dToBcd (time / 100 / 100) ;	// hours
  clock [ 3] = dToBcd (date % 100) ;	// date
  clock [ 4] = dToBcd (date / 100 % 100) ;	// months 0-11 --> 1-12
  clock [ 5] = dToBcd (weekday) ;	// weekdays (sun 0)
  clock [ 6] = dToBcd (date / 100 / 100) ;       // years
  clock [ 7] = 0 ;			// W-Protect off

  ds1302clockWrite (clock) ;

  printf ("OK\n") ;

  return 0 ;
}




int main (int argc, char *argv [])
{
  int i ;
  int clock [8] ;
  int year ;
  int month ;
  int date ;
  int hour ;
  int minute ;
  int second ;
  int weekday ;

  wiringPiSetup () ;
  ds1302setup   (0, 1, 2) ;

  if (argc == 2)
  {
    /**/ if (strcmp (argv [1], "-slc") == 0)
      return setLinuxClock () ;
    else if (strcmp (argv [1], "-sdsc") == 0)
      return setDSclock () ;
    else if (strcmp (argv [1], "-rtest") == 0)
      return ramTest () ;
    else
    {
      printf ("Usage: ds1302 [-slc | -sdsc | -rtest]\n") ;
      return EXIT_FAILURE ;
    }
  }

  for (i = 0 ;; ++i)
  {
    printf ("%5d:  ", i) ;

    ds1302clockRead (clock) ;
    
	hour   = bcdToD (clock [2], masks [2]) ;
	minute = bcdToD (clock [1], masks [1]) ;
	second = bcdToD (clock [0], masks [0]) ;

    date  = bcdToD (clock [3], masks [3]) ;
	month = bcdToD (clock [4], masks [4]) ;
	year  = bcdToD (clock [6], masks [6]) + 2000 ;
	weekday = bcdToD (clock [5], masks [5]) ;

	printf ("  %04d-%02d-%02d", year, month, date) ;
	printf ("  %02d:%02d:%02d", hour, minute, second) ;
    
    switch (weekday){
      case 0: printf ("  SUN") ; break;
	  case 1: printf ("  MON") ; break;
	  case 2: printf ("  TUE") ; break;
	  case 3: printf ("  WED") ; break;
	  case 4: printf ("  THU") ; break;
	  case 5: printf ("  FRI") ; break;
	  case 6: printf ("  SAT") ; break;
	}

    printf ("\n") ;

    delay (200) ;
  }
 
  return 0 ;
}




Pythoon Code



#!/usr/bin/env python
#-----------------------------------------------------
#
#		This is a program for DS1302 RTC Module.
#	It provide precision timmer.
#
#		This program depend on rpi_time.py. 
#
#		ds1302 Module 			   Pi
#			VCC ------------------ 5 V (Must be 5v)
#			GND ------------------ GND
#			SCL ---------------- Pin 16
#			SDA ---------------- Pin 18
#			RST ---------------- Pin 22
#
#-----------------------------------------------------
from datetime import datetime
import ds1302
import rpi_time
import time

rtc = rpi_time.DS1302()

def setup():
	print ''
	print ''
	print rtc.get_datetime()
	print ''
	print ''
	a = raw_input( "Do you want to setup date and time?(y/n) ")
	if a == 'y' or a == 'Y':
		date = raw_input("Input date:(YYYY MM DD) ")
		time = raw_input("Input time:(HH MM SS) ")
		date = date.split()
		time = time.split()
		print ''
		print ''
		ds1302.set_date(int(date[0]), int(date[1]), int(date[2]))
		ds1302.set_time(int(time[0]), int(time[1]), int(time[2]))
		dt = rtc.get_datetime()
		print "You set the date and time to:", dt

def loop():
	while True:
		a = rtc.get_datetime()
		print a
		time.sleep(0.5)

def destory():
	GPIO.cleanup()				# Release resource

if __name__ == '__main__':		# Program start from here
	setup()
	try:
		loop()
	except KeyboardInterrupt:  	# When 'Ctrl+C' is pressed, the child program destroy() will be  executed.
		destory()


 

 

 


Copyright © 2012 - 2016 SunFounder. All Rights Reserved.


Previous chapter: Lesson 32 MPU6050 Gyro Acceleration Sensor

Next chapter: Lesson 34 Tracking Sensor

SunFounder
Apr 15 2017 at 06:10 am



© Developed by CommerceLab