Arduino Project

Arduino Automatic Barrier Gate Project with Ultrasonic Sensor V2

Course Introduction

In this lesson, you’ll learn how to use an ultrasonic sensor module, a digital servo motor, and Traffic light LED Module with the Arduino Board to build an intelligent barrier gate system version 2.0.

When the ultrasonic sensor module detects a vehicle, the traffic light will change from red to green, and the gate will rise, allowing the car to pass.

Note

If this is your first time working with an Arduino project, we recommend downloading and reviewing the basic materials first.

1.1 Install Arduino IDE(Important)
1.2 Introduction of Arduino IDE

Required Components

In this project, we need the following components:

SN	COMPONENT INTRODUCTION	QUANTITY	PURCHASE LINK
1	Arduino UNO R4 Minima/Arduino UNO R4 WIFI	1	BUY
2	USB Type-C cable	1	×
3	Breadboard	1	BUY
4	Wires	Several	BUY
5	LED Module	1	BUY
6	I2C LCD 1602	1	BUY
7	Ultrasonic Sensor Module	1	BUY
8	Digital Servo Motor	1	BUY
9	Traffic Light LED	1	BUY

Wiring

15.webp__PID:3abea4bf-1b37-4cdb-bd22-e26d75bdf1f5

Common Connections:

Traffic light LED
R: Connect to 11 on the Arduino.
Y: Connect to 10 on the Arduino.
G: Connect to 9 on the Arduino.
GND: Connect to breadboard’s negative power bus.

Ultrasonic Sensor Module
Trig: Connect to 3 on the Arduino.
Echo: Connect to 4 on the Arduino.
GND: Connect to breadboard’s negative power bus.
VCC: Connect to breadboard’s red power bus.

Digital Servo Motor
Connect to breadboard’s positive power bus.
Connect to breadboard’s negative power bus.
Connect to 12 on the Arduino.

I2C LCD 1602
SDA: Connect to A4 on the Arduino.
SCL: Connect to A5 on the Arduino.
GND: Connect to breadboard’s negative power bus.
VCC: Connect to breadboard’s red power bus.

Writing the Code

Note
You can copy this code into Arduino IDE.
To install the library, use the Arduino Library Manager and search for LiquidCrystal I2C and install it.
Don’t forget to select the board(Arduino UNO R4 WIFI) and the correct port before clicking the Upload button.

#include <Servo.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>

// Define pin connections
const int trigPin = 3;
const int echoPin = 4;
const int redPin = 11;
const int yellowPin = 10;
const int greenPin = 9;
const int servoPin = 12;

// Create LCD and Servo objects
Servo myServo;
LiquidCrystal_I2C lcd(0x27, 16, 2); // 16x2 I2C LCD

void setup() {
  Serial.begin(9600);

  pinMode(trigPin, OUTPUT);
  pinMode(echoPin, INPUT);
  pinMode(redPin, OUTPUT);
  pinMode(yellowPin, OUTPUT);
  pinMode(greenPin, OUTPUT);

  myServo.attach(servoPin);
  myServo.write(90); // Start with gate closed

  lcd.init();
  lcd.backlight();
  lcd.clear();
  lcd.setCursor(2, 0);  // Center "System Ready"
  lcd.print("System Ready");
  delay(1000);
}

void loop() {
  // Send ultrasonic pulse
  digitalWrite(trigPin, LOW);
  delayMicroseconds(2);
  digitalWrite(trigPin, HIGH);
  delayMicroseconds(10);
  digitalWrite(trigPin, LOW);

  // Measure duration of echo
  long duration = pulseIn(echoPin, HIGH);
  float distance = duration * 0.034 / 2;

  Serial.print("Distance: ");
  Serial.print(distance);
  Serial.println(" cm");

  if (distance < 10) {  // Vehicle detected
    digitalWrite(redPin, LOW);
    digitalWrite(yellowPin, HIGH);
    digitalWrite(greenPin, LOW);
    myServo.write(90); // Keep gate closed

    lcd.clear();
    lcd.setCursor(2, 0);  // Center "Please Wait"
    lcd.print("Please Wait");

    delay(1000); // Wait 1 seconds with yellow light

    digitalWrite(yellowPin, LOW);
    digitalWrite(greenPin, HIGH);
    myServo.write(0); // Open gate

    lcd.clear();
    lcd.setCursor(1, 0);  // Center "You Can Pass!"
    lcd.print("You Can Pass!");

    delay(1500); // Wait 1.5 seconds with green light

    digitalWrite(greenPin, LOW);
    digitalWrite(redPin, HIGH);
    myServo.write(90); // Close gate

    lcd.clear();
    lcd.setCursor(4, 0);  // Center "Welcome"
    lcd.print("Welcome");
  } else {
    digitalWrite(redPin, HIGH);
    digitalWrite(yellowPin, LOW);
    digitalWrite(greenPin, LOW);
    myServo.write(90); // Keep gate closed

    lcd.clear();
    lcd.setCursor(4, 0);  // Center "Welcome"
    lcd.print("Welcome");
  }

  delay(300); // Small delay before next reading
}

Recover password

Create my account

Arduino Project

Arduino Automatic Barrier Gate Project with Ultrasonic Sensor V2

Course Introduction

Required Components

Wiring

Common Connections:

Writing the Code

Arduino Project

Arduino Automatic Barrier Gate Project with Ultrasonic Sensor V2

Course Introduction

Required Components

Wiring

Common Connections:

Writing the Code

Subscribe to our newsletter