Arduino Project

Arduino LED Chaser with Multiple LEDs

Kit purchase

Looking for parts? Check out our all-in-one kits below — packed with components, beginner-friendly guides, and tons of fun.

2.webp__PID:7d088a16-8752-49fb-8b1f-f9bba7297987

Name	Includes Arduino board	PURCHASE LINK
Elite Explorer Kit	Arduino Uno R4 WiFi	BUY
3 in 1 Ultimate Starter Kit	Arduino Uno R4 Minima	BUY
Ultimate Sensor Kit	Arduino Uno R4 Minima	BUY
Universal Maker Sensor Kit	×	BUY

Course Introduction

In this lesson, you will learn how to use Arduino with LEDs, a potentiometer, a button, and an active buzzer to create a running light effect.

Rotate the potentiometer to adjust the speed of the flowing LEDs. Press the button to pause the light at its current position or resume the animation, while the buzzer beeps in sync with the movement.

Note

If this is your first time working with an Arduino project, we recommend downloading and reviewing the basic materials first.

1.1 Install Arduino IDE(Important)
1.2 Introduction of Arduino IDE

Required Components

In this project, we need the following components:

SN	COMPONENT INTRODUCTION	QUANTITY	PURCHASE LINK
1	Arduino UNO R4 Minima	1	BUY
2	USB Type-C cable	1	×
3	Breadboard	1	BUY
4	Wires	Several	BUY
5	220Ω resistor	1	BUY
6	Button	2	BUY
7	LED	1	BUY
8	Active Buzzer	1	×
9	Potentiometer Sensor Module	1	BUY

Wiring

6.png__PID:f260ace1-804e-458f-a5b2-c41d27b21d6d

Common Connections:

LED
Connect the LEDs cathode to the negative power bus on the breadboard, and the LEDs anode to a 220Ω resistor then to 3 to 10 on the Arduino.

Button
Connect to breadboard’s negative power bus.
Connect to 2 on the Arduino.

Active Buzzer
＋: Connect to 11 on the Arduino.
－: Connect to breadboard’s negative power bus.

Potentiometer Sensor Module
OUT: Connect to A0 on the Arduino.
GND: Connect to breadboard’s negative power bus.
VCC: Connect to breadboard’s red power bus.

Writing the Code

Note
You can copy this code into Arduino IDE.
Don’t forget to select the board(Arduino UNO R4 Minima) and the correct port before clicking the Upload button.

  // LED pins
const int ledPins[] = {3, 4, 5, 6, 7, 8, 9, 10};
const int ledCount = 8;

// Potentiometer pin
const int POT_PIN = A0;

// Button pin
const int BUTTON_PIN = 2;

// Active buzzer pin
const int BUZZER_PIN = 11;

int currentLed = 0;
bool isRunning = true;

unsigned long lastLedTime = 0;
unsigned long lastButtonTime = 0;
unsigned long buzzerStartTime = 0;

const unsigned long debounceDelay = 200;
const unsigned long buzzerBeepTime = 40;

bool lastButtonState = HIGH;
bool buzzerActive = false;

void setup() {
  for (int i = 0; i < ledCount; i++) {
    pinMode(ledPins[i], OUTPUT);
    digitalWrite(ledPins[i], LOW);
  }

  pinMode(BUTTON_PIN, INPUT_PULLUP);
  pinMode(BUZZER_PIN, OUTPUT);

  digitalWrite(BUZZER_PIN, LOW);
  digitalWrite(ledPins[currentLed], HIGH);
}

void loop() {
  handleButton();
  handleBuzzer();

  if (isRunning) {
    int potValue = analogRead(POT_PIN);

    // Adjust flowing speed with the potentiometer
    int flowDelay = map(potValue, 0, 1023, 80, 800);

    if (millis() - lastLedTime >= flowDelay) {
      lastLedTime = millis();

      digitalWrite(ledPins[currentLed], LOW);

      currentLed++;
      if (currentLed >= ledCount) {
        currentLed = 0;
      }

      digitalWrite(ledPins[currentLed], HIGH);

      beepOnce();
    }
  }
}

void handleButton() {
  bool currentButtonState = digitalRead(BUTTON_PIN);

  if (lastButtonState == HIGH && currentButtonState == LOW) {
    if (millis() - lastButtonTime > debounceDelay) {
      isRunning = !isRunning;
      lastButtonTime = millis();

      beepOnce();

      if (!isRunning) {
        delay(60);
        digitalWrite(BUZZER_PIN, LOW);
        buzzerActive = false;
      }
    }
  }

  lastButtonState = currentButtonState;
}

void beepOnce() {
  digitalWrite(BUZZER_PIN, HIGH);
  buzzerStartTime = millis();
  buzzerActive = true;
}

void handleBuzzer() {
  if (buzzerActive && millis() - buzzerStartTime >= buzzerBeepTime) {
    digitalWrite(BUZZER_PIN, LOW);
    buzzerActive = false;
  }
}

Recover password

Create my account

Arduino Project

Arduino LED Chaser with Multiple LEDs

Kit purchase

Course Introduction

Required Components

Wiring

Common Connections:

Writing the Code

Arduino Project

Arduino LED Chaser with Multiple LEDs

Kit purchase

Course Introduction

Required Components

Wiring

Common Connections:

Writing the Code

Subscribe to our newsletter