Arduino Project

Arduino Light Tracker with LDR and Servo V2

Kit purchase

Looking for parts? Check out our all-in-one kits below — packed with components, beginner-friendly guides, and tons of fun.

2.png__PID:4c058c33-95c6-4f46-b6eb-562b4ffd4bdf

Name	Includes Arduino board	PURCHASE LINK
Elite Explorer Kit	Arduino Uno R4 WiFi	BUY
3 in 1 Ultimate Starter Kit	Arduino Uno R4 Minima	BUY

Course Introduction

This Arduino project uses two photoresistors (LDRs) to detect light direction and control a servo motor.

The servo turns smoothly toward the side with brighter light, allowing the system to follow changes in lighting. By adjusting the target angle gradually, the code ensures stable and jitter-free movement. This setup is great for building light-seeking robots or automatic sun trackers.

Note

If this is your first time working with an Arduino project, we recommend downloading and reviewing the basic materials first.

1.1 Install Arduino IDE(Important)
1.2 Introduction of Arduino IDE

Required Components

In this project, we need the following components:

SN	COMPONENT INTRODUCTION	QUANTITY	PURCHASE LINK
1	Arduino UNO R4 WIFI	1	BUY
2	USB Type-C cable	1	×
3	Breadboard	1	BUY
4	Wires	Several	BUY
5	Digital Servo Motor	1	BUY
6	Photoresistor	2	BUY

Wiring

4.webp__PID:3d147482-8613-4d59-bdd2-1de4d7329c66

Common Connections:

Digital Servo Motor
Connect to breadboard’s positive power bus.
Connect to breadboard’s negative power bus.
Connect to 9 on the Arduino.

Photoresistor Module
Connect to A0 on the Arduino.
Connect to breadboard’s negative power bus.

Photoresistor LEFT
Connect to A5 on the Arduino.
Connect to breadboard’s negative power bus.

Writing the Code

Note
You can copy this code into Arduino IDE.
Don’t forget to select the board(Arduino UNO R4 Minima/WIFI) and the correct port before clicking the Upload button.

#include <Servo.h>

Servo myservo;

int angle = 90;           // current servo angle
int targetAngle = 90;     // target servo angle
unsigned long lastMoveTime = 0;
const int moveInterval = 30; // time between movements (ms)
const int step = 1;          // servo moves 1° each time

void setup() {
  Serial.begin(9600);
  myservo.attach(9);
  myservo.write(angle);  // set initial angle to 90°
}

void loop() {
  int sensorLeft = analogRead(A0);  // read left photoresistor (A0)
  int sensorRight = analogRead(A5); // read right photoresistor (A5)

  // print both sensor values
  Serial.print("A0: ");
  Serial.print(sensorLeft);
  Serial.print("  A5: ");
  Serial.println(sensorRight);

  // set target angle based on light level
  if (sensorLeft > 950) {
    targetAngle = 180;  // if A0 is bright, turn right
  } else if (sensorRight > 950) {
    targetAngle = 0;    // if A5 is bright, turn left
  }

  // move servo gradually without delay
  unsigned long currentTime = millis();
  if (currentTime - lastMoveTime >= moveInterval) {
    lastMoveTime = currentTime;

    if (angle < targetAngle) {
      angle += step;
      if (angle > targetAngle) angle = targetAngle;
      myservo.write(angle);
    } else if (angle > targetAngle) {
      angle -= step;
      if (angle < targetAngle) angle = targetAngle;
      myservo.write(angle);
    }
  }
}

Recover password

Create my account

Arduino Project

Arduino Light Tracker with LDR and Servo V2

Kit purchase

Course Introduction

Required Components

Wiring

Common Connections:

Writing the Code

Arduino Project

Arduino Light Tracker with LDR and Servo V2

Kit purchase

Course Introduction

Required Components

Wiring

Common Connections:

Writing the Code

Subscribe to our newsletter