Arduino Project

Arduino Parking Sensor with Ultrasonic Sensor V1

Kit purchase

Looking for parts? Check out our all-in-one kits below — packed with components, beginner-friendly guides, and tons of fun.

2.webp__PID:7d088a16-8752-49fb-8b1f-f9bba7297987

Name	Includes Arduino board	PURCHASE LINK
Elite Explorer Kit	Arduino Uno R4 WiFi	BUY
3 in 1 Ultimate Starter Kit	Arduino Uno R4 Minima	BUY
Ultimate Sensor Kit	Arduino Uno R4 Minima	BUY
Universal Maker Sensor Kit	×	BUY

Course Introduction

In this lesson, you’ll learn how to create a parking sensor system using the Ultrasonic Sensor Module and MAX7219 Dot Matrix Module.

As an obstacle gets closer to the sensor, the distance will be displayed on the dot matrix module.

Note

If this is your first time working with an Arduino project, we recommend downloading and reviewing the basic materials first.

1.1 Install Arduino IDE(Important)
1.2 Introduction of Arduino IDE

Required Components

In this project, we need the following components:

SN	COMPONENT INTRODUCTION	QUANTITY	PURCHASE LINK
1	Arduino UNO R4 Minima	1	BUY
2	USB Type-C cable	1	×
3	Breadboard	1	BUY
4	Wires	Several	BUY
5	Joystick Module	1	BUY
6	MAX7219 Dot Matrix Module	1	BUY
7	Ultrasonic Sensor Module	1	BUY

Wiring

6.webp__PID:5e337b32-2cec-46c1-9a53-e836e1d9b36a

Common Connections:

MAX7219 Dot Matrix Module
CLK: Connect to 11 on the Arduino.
CS: Connect to 10 on the Arduino.
DIN: Connect to 12 on the Arduino.
GND: Connect to breadboard’s negative power bus.
VCC: Connect to breadboard’s red power bus.

Ultrasonic Sensor Module
Trig: Connect to 4 on the Arduino.
Echo: Connect to 3 on the Arduino.
GND: Connect to breadboard’s negative power bus.
VCC: Connect to breadboard’s red power bus.

Writing the Code

Note
You can copy this code into Arduino IDE.
To install the library, use the Arduino Library Manager and search for LedControl and install it.
Don’t forget to select the board(Arduino UNO R4 WiFi) and the correct port before clicking the Upload button.

#include "LedControl.h"

// Initialize the LedControl object for 4 connected modules
LedControl lc = LedControl(12, 11, 10, 4);

// Define pins for ultrasonic sensor
const int echoPin = 3; // Echo pin for the ultrasonic sensor
const int trigPin = 4; // Trigger pin for the ultrasonic sensor

// 8x8 dot matrix representations of numbers 0-9
byte numbers[10][8] = {
    {0x3C, 0x42, 0x42, 0x42, 0x42, 0x42, 0x42, 0x3C}, // 0
    {0x08, 0x18, 0x38, 0x08, 0x08, 0x08, 0x08, 0x7E}, // 1
    {0x3C, 0x42, 0x40, 0x20, 0x10, 0x08, 0x04, 0x7E}, // 2
    {0x3C, 0x42, 0x40, 0x30, 0x40, 0x40, 0x42, 0x3C}, // 3
    {0x20, 0x30, 0x28, 0x24, 0x7E, 0x20, 0x20, 0x20}, // 4
    {0x7E, 0x02, 0x1E, 0x20, 0x40, 0x40, 0x42, 0x3C}, // 5
    {0x3C, 0x02, 0x02, 0x1E, 0x22, 0x42, 0x42, 0x3C}, // 6
    {0x7E, 0x40, 0x20, 0x10, 0x08, 0x08, 0x08, 0x08}, // 7
    {0x3C, 0x42, 0x42, 0x3C, 0x42, 0x42, 0x42, 0x3C}, // 8
    {0x3C, 0x42, 0x42, 0x3C, 0x40, 0x40, 0x40, 0x3C}  // 9
};

unsigned long lastMeasurementTime = 0;
const int measurementInterval = 400; // Interval for distance measurements
const int animationInterval = 40; // Refresh interval for animations
unsigned long lastAnimationTime = 0;
int targetColumnsLit = 0;
int currentCol = 0;

void setup() {
  Serial.begin(9600);
  pinMode(echoPin, INPUT);
  pinMode(trigPin, OUTPUT);

  // Initialize all LED modules
  for (int i = 0; i < 4; i++) {
    lc.shutdown(i, false);
    lc.setIntensity(i, 8);
    lc.clearDisplay(i);
  }
}

void loop() {
  // Measure distance
  if (millis() - lastMeasurementTime >= measurementInterval) {
    lastMeasurementTime = millis();
    float distance = readDistance();
    Serial.print("Distance: ");
    Serial.print(distance);
    Serial.println(" cm");

    // Update the displayed number based on the measured distance
    int displayValue = constrain((int)distance, 0, 99);
    displayNumber(displayValue);

    // Update the target number of columns to light up based on distance
    targetColumnsLit = calculateColumnsToLight(distance);
  }

  // Update the animation display
  updateAnimation();
}

float readDistance() {
  digitalWrite(trigPin, LOW);
  delayMicroseconds(2);
  digitalWrite(trigPin, HIGH);
  delayMicroseconds(10);
  digitalWrite(trigPin, LOW);
  float distance = pulseIn(echoPin, HIGH) / 58.00;
  return distance > 400 ? 400 : distance; // Limit max measurement distance
}

void displayNumber(int number) {
  lc.clearDisplay(2); // Clear display module 2
  lc.clearDisplay(3); // Clear display module 3
  if (number < 10) {
    displayDigit(2, number); // Display a single digit on module 3
  } else {
    displayDigit(2, number % 10); // Unit digit on module 2
    displayDigit(3, number / 10); // Tens digit on module 3
  }
}

void displayDigit(int module, int digit) {
  for (int row = 0; row < 8; row++) {
    byte reversed = needsMirror(digit) ? reverseByte(numbers[digit][row]) : numbers[digit][row];
    lc.setRow(module, row, reversed);
  }
}

bool needsMirror(int digit) {
  return (digit == 2 || digit == 3 || digit == 4 || digit == 5 || digit == 6 || digit == 7 || digit == 9);
}

byte reverseByte(byte b) {
  b = (b & 0xF0) >> 4 | (b & 0x0F) << 4;
  b = (b & 0xCC) >> 2 | (b & 0x33) << 2;
  b = (b & 0xAA) >> 1 | (b & 0x55) << 1;
  return b;
}

int calculateColumnsToLight(float distance) {
  return constrain(map(distance, 21, 0, 0, 18), 0, 16);
}

void updateAnimation() {
  if (millis() - lastAnimationTime >= animationInterval) {
    lastAnimationTime = millis();
    if (currentCol < targetColumnsLit) {
      lightUpColumn(currentCol, true);
      currentCol++;
    } else if (currentCol > targetColumnsLit) {
      currentCol--;
      lightUpColumn(currentCol, false);
    }
  }
}

void lightUpColumn(int col, bool state) {
  int matrixIndex = 1 - (col / 8);
  int colIndex = col % 8;
  for (int row = 0; row < (col / 2) + 1; row++) {
    lc.setLed(matrixIndex, 7 - row, colIndex, state);
  }
}

Recover password

Create my account

Arduino Project

Arduino Parking Sensor with Ultrasonic Sensor V1

Kit purchase

Course Introduction

Required Components

Wiring

Common Connections:

Writing the Code

Arduino Project

Arduino Parking Sensor with Ultrasonic Sensor V1

Kit purchase

Course Introduction

Required Components

Wiring

Common Connections:

Writing the Code

Subscribe to our newsletter