Arduino Project

Arduino Speed Detector Project with Ultrasonic Sensors V1

Course Introduction

This Arduino project functions as a basic speed detection system using two infrared (IR) sensors and an LCD display.

When a vehicle passes the front sensor, the system starts a timer; it stops the timer once the vehicle triggers the back sensor.

Using the known distance between the sensors, the system calculates the vehicle’s speed and displays it in km/h on a 16x2 I2C LCD.

If the speed exceeds a set threshold (e.g., 60 km/h), a buzzer alerts for overspeeding. The LCD resets after each detection cycle, ready for the next vehicle.

Note

If this is your first time working with an Arduino project, we recommend downloading and reviewing the basic materials first.

1.1 Install Arduino IDE(Important)
1.2 Introduction of Arduino IDE

Required Components

In this project, we need the following components:

SN	COMPONENT INTRODUCTION	QUANTITY	PURCHASE LINK
1	Arduino UNO R4 Minima/Arduino UNO R4 WIFI	1	BUY
2	USB Type-C cable	1	×
3	Breadboard	1	BUY
4	Wires	Several	BUY
5	DC Motor	1	BUY
6	IR Obstacle Avoidance Sensor Module	2	BUY
7	I2C LCD 1602	1	BUY

Wiring

9.webp__PID:2825d525-502e-41dd-acbe-1b985a7ad0a9

Common Connections:

Passive Buzzer
＋: Connect to 4 on the Arduino.
－: Connect to breadboard’s negative power bus.

I2C LCD 1602
SDA: Connect to A4 on the Arduino.
SCL: Connect to A5 on the Arduino.
GND: Connect to breadboard’s negative power bus.
VCC: Connect to breadboard’s red power bus.

IR Obstacle Avoidance Sensor Module Front
OUT: Connect to 2 on the Arduino.
GND: Connect to breadboard’s negative power bus.
VCC: Connect to breadboard’s red power bus.

IR Obstacle Avoidance Sensor Module Back
OUT: Connect to 3 on the Arduino.
GND: Connect to breadboard’s negative power bus.
VCC: Connect to breadboard’s red power bus

Writing the Code

Note
You can copy this code into Arduino IDE.
To install the library, use the Arduino Library Manager and search for LiquidCrystal I2C and install it.
Don’t forget to select the board(Arduino UNO R4 WIFI) and the correct port before clicking the Upload button.

#include <Wire.h>
#include <LiquidCrystal_I2C.h>

// Initialize LCD with I2C address 0x27, 16 columns and 2 rows
LiquidCrystal_I2C lcd(0x27, 16, 2); // Common I2C addresses: 0x27 or 0x3F

// Define pin numbers for IR sensors and buzzer
const int irFront = 2;   // Front IR sensor connected to digital pin 2
const int irBack = 3;    // Back IR sensor connected to digital pin 3
const int buzzer = 4;    // Active buzzer connected to digital pin 4

unsigned long t1 = 0, t2 = 0; // Time markers for calculating speed
bool carDetected = false;    // Flag to track if a car has been detected
float distance = 1.30;       // Distance between IR sensors in meters (e.g. 1.30 meters)

void setup() {
  pinMode(irFront, INPUT);   // Set front IR sensor as input
  pinMode(irBack, INPUT);    // Set back IR sensor as input
  pinMode(buzzer, OUTPUT);   // Set buzzer pin as output

  lcd.init();                // Initialize the LCD
  lcd.backlight();           // Turn on LCD backlight
  lcd.setCursor(0, 0);
  lcd.print("No car detected"); // Display default message
}

void loop() {
  // Wait for a car to pass the front sensor
  if (!carDetected && digitalRead(irFront) == LOW) {
    carDetected = true;        // Mark that a car has been detected
    t1 = millis();             // Record time when front sensor is triggered

    lcd.clear();
    lcd.setCursor(0, 0);
    lcd.print("searching...");

    while (digitalRead(irBack) == HIGH); // Wait until back sensor is triggered
    t2 = millis();             // Record time when back sensor is triggered

    unsigned long deltaT = t2 - t1;        // Calculate time difference in milliseconds
    float timeSec = deltaT / 1000.0;       // Convert time to seconds
    float speed = (distance / timeSec) * 3.6; // Calculate speed in km/h

    lcd.clear();
    lcd.setCursor(0, 0);
    lcd.print("SPeed: ");
    lcd.print((int)speed);
    lcd.print("KM/Hr");

    lcd.setCursor(0, 1);
    if (speed <= 60.0) {
      lcd.print("Normal Sreed");         // Display if speed is within limit
    } else {
      lcd.print("Over Speeding");        // Display warning for overspeed
      digitalWrite(buzzer, HIGH);        // Turn on buzzer
      delay(1000);                       // Wait 1 second
      digitalWrite(buzzer, LOW);         // Turn off buzzer
    }

    delay(3000);                          // Display result for 3 seconds
    lcd.clear();
    lcd.setCursor(0, 0);
    lcd.print("No car detected");        // Reset to default message
    carDetected = false;                 // Ready for next car
  }
}

Recover password

Create my account

Arduino Project

Arduino Speed Detector Project with Ultrasonic Sensors V1

Course Introduction

Required Components

Wiring

Common Connections:

Writing the Code

Arduino Project

Arduino Speed Detector Project with Ultrasonic Sensors V1

Course Introduction

Required Components

Wiring

Common Connections:

Writing the Code

Subscribe to our newsletter