Arduino Project

Arduino Water Level Indicator with Water Level Sensor V1

Kit purchase

Looking for parts? Check out our all-in-one kits below — packed with components, beginner-friendly guides, and tons of fun.

2.png__PID:4c058c33-95c6-4f46-b6eb-562b4ffd4bdf

Name	Includes Arduino board	PURCHASE LINK
Elite Explorer Kit	Arduino Uno R4 WiFi	BUY
3 in 1 Ultimate Starter Kit	Arduino Uno R4 Minima	BUY

Course Introduction

In this lesson, you’ll learn how to use an Ultrasonic Sensor Module, a 1602 LCD with the Arduino UNO R4 to create a Ultrasonic water level monitor system.

The LED lights red when the water is low, turns yellow as it rises, and switches to green once it reaches the set level.

Note

If this is your first time working with an Arduino project, we recommend downloading and reviewing the basic materials first.

1.1 Install Arduino IDE(Important)
1.2 Introduction of Arduino IDE

Required Components

In this project, we need the following components:

SN	COMPONENT INTRODUCTION	QUANTITY	PURCHASE LINK
1	Arduino UNO R4 Minima/Arduino UNO R4 WIFI	1	BUY
2	USB Type-C cable	1	×
3	Breadboard	1	BUY
4	Wires	Several	BUY
5	I2C LCD 1602	1	BUY
6	Resistor	1KΩ	BUY
7	Ultrasonic Sensor Module	1	BUY
8	LED	3	BUY

Wiring

8.webp__PID:d522f7cf-0f3c-4d33-a37b-8ddf071af9ef

Common Connections:

Ultrasonic Sensor Module
Trig: Connect to 4 on the Arduino.
Echo: Connect to 3on the Arduino.
GND: Connect to breadboard’s negative power bus.
VCC: Connect to breadboard’s red power bus

I2C LCD 1602
SDA: Connect to A4 on the Arduino.
SCL: Connect to A5 on the Arduino.
GND: Connect to breadboard’s negative power bus.
VCC: Connect to breadboard’s red power bus.

LEDS
Green: Connect the LED cathode to the negative power bus on the breadboard, and the anode to a 1KΩ resistor, then to 5 on the Arduino.
Yellow: Connect the LED cathode to the negative power bus on the breadboard, and the anode to a 1kΩ resistor, then to 6 on the Arduino.
Red: Connect the LED cathode to the negative power bus on the breadboard, and the anode to a 1kΩ resistor, then to 7 on the Arduino.

Writing the Code

Note
You can copy this code into Arduino IDE.
To install the library, use the Arduino Library Manager and search for LiquidCrystal I2C and install it.
Don’t forget to select the board(Arduino UNO R4 WiFi) and the correct port before clicking the Upload button.

#include <LiquidCrystal_I2C.h>

// Initialize the LCD (I2C address 0x27, 16 columns, 2 rows)
LiquidCrystal_I2C lcd(0x27, 16, 2);

// Define the pins for the ultrasonic sensor
const int echoPin = 3;
const int trigPin = 4;

// Define the pins for the LEDs
const int greenLed = 7;   // Green LED connected to pin 7
const int yellowLed = 6;  // Yellow LED connected to pin 6
const int redLed = 5;     // Red LED connected to pin 5
void setup() {
  // Initialize the LCD and clear the lcd
  lcd.init();
  lcd.clear();
  lcd.backlight();

  // Initialize ultrasonic sensor pins
  pinMode(echoPin, INPUT);
  pinMode(trigPin, OUTPUT);

  // Initialize LED pins
  pinMode(greenLed, OUTPUT);
  pinMode(yellowLed, OUTPUT);
  pinMode(redLed, OUTPUT);
}

void loop() {
  // Get the distance to the water level
  float distance = readDistance();

  // Display the distance on the LCD
  lcd.setCursor(0, 0);
  lcd.print("Distance:");
  lcd.setCursor(0, 1);
  lcd.print(distance);
  lcd.print(" cm  ");

  // Light up the corresponding LED based on the distance
  if (distance <= 5) {
    // Distance 0-5 cm, turn on the green LED
    digitalWrite(greenLed, HIGH);
    digitalWrite(yellowLed, LOW);
    digitalWrite(redLed, LOW);
  } else if (distance > 5 && distance <= 10) {
    // Distance 5-10 cm, turn on the yellow LED
    digitalWrite(greenLed, LOW);
    digitalWrite(yellowLed, HIGH);
    digitalWrite(redLed, LOW);
  } else if (distance > 10 && distance <= 15) {
    // Distance 10-15 cm, turn on the red LED
    digitalWrite(greenLed, LOW);
    digitalWrite(yellowLed, LOW);
    digitalWrite(redLed, HIGH);
  } else {
    // Distance greater than 15 cm, turn off all LEDs
    digitalWrite(greenLed, LOW);
    digitalWrite(yellowLed, LOW);
    digitalWrite(redLed, LOW);
  }

  delay(500);  // Delay 500 milliseconds
}

// Read the distance from the ultrasonic sensor
float readDistance() {
  digitalWrite(trigPin, LOW);  // Ensure the trigger pin is low
  delayMicroseconds(2);
  digitalWrite(trigPin, HIGH); // Trigger the ultrasonic sensor to send a pulse
  delayMicroseconds(10);
  digitalWrite(trigPin, LOW);  // End the trigger

  // Measure the pulse width of the echo pin and convert it to distance
  float distance = pulseIn(echoPin, HIGH) / 58.00;
  return distance;
}

Recover password

Create my account

Arduino Project

Arduino Water Level Indicator with Water Level Sensor V1

Kit purchase

Course Introduction

Required Components

Wiring

Common Connections:

Writing the Code

Arduino Project

Arduino Water Level Indicator with Water Level Sensor V1

Kit purchase

Course Introduction

Required Components

Wiring

Common Connections:

Writing the Code

Subscribe to our newsletter