Arduino Project

Heart Rate Sensor Module

Course Introduction

In this lesson, we will learn how to use the Heart Rate Sensor Module with Arduino.

Note

If this is your first time working with an Arduino project, we recommend downloading and reviewing the basic materials first.

1.1 Install Arduino IDE(Important)
1.2 Introduction of Arduino IDE

Required Components

In this project, we need the following components:

SN

COMPONENT INTRODUCTION

QUANTITY

PURCHASE LINK

1

Arduino UNO R4 WIFI

1

BUY

2

USB Type-C cable

1

×

3

Breadboard

1

BUY

4

Wires

Several

BUY

5

Pulse Oximeter and Heart Rate Sensor Module (MAX30102)

1

BUY

Wiring

1.png__PID:71189e6b-f73d-4d8e-985f-c16bc0a56f84

Common Connections:

Pulse Oximeter and Heart Rate Sensor Module (MAX30102)
SDA: Connect to A4 on the Arduino.
SCL: Connect to A5 on the Arduino.
GND: Connect to breadboard’s negative power bus.
VIN: Connect to breadboard’s red power bus.

Writing the Code

Note
You can copy this code into Arduino IDE.
To install the library, use the Arduino Library Manager and search for MAX30105 and heartRate and install it.
Don’t forget to select the board(Arduino UNO R4 WIFI) and the correct port before clicking the Upload button.


/*
  This is a demo to show the reading of heart rate or beats per minute (BPM).

  It is best to attach the sensor to your finger using a rubber band or other tightening
  device. Humans are generally bad at applying constant pressure to a thing. When you
  press your finger against the sensor it varies enough to cause the blood in your
  finger to flow differently which causes the sensor readings to go wonky.

  Board: Arduino Uno R3 (or R4)
  Component: Pulse Oximeter and Heart Rate Sensor(MAX30102)
  Library: https://github.com/sparkfun/SparkFun_MAX3010x_Sensor_Library  (SparkFun MAX3010x Pulse and Proximity Sensor Library)
*/

#include 
#include "MAX30105.h"
#include "heartRate.h"

MAX30105 particleSensor;

const byte RATE_SIZE = 4;  //Increase this for more averaging. 4 is good.
byte rates[RATE_SIZE];     //Array of heart rates
byte rateSpot = 0;
long lastBeat = 0;  //Time at which the last beat occurred

float beatsPerMinute;  //Current BPM value
int beatAvg;           //Average BPM value

void setup() {

  Serial.begin(9600);
  Serial.println("Initializing...");

  // Initialize sensor
  if (!particleSensor.begin(Wire, I2C_SPEED_FAST))  //Use default I2C port, 400kHz speed
  {
    Serial.println("MAX30102 was not found. Please check wiring/power. ");
    while (1) ; //Infinite loop to stop the program
  }
  Serial.println("Place your index finger on the sensor with steady pressure.");

  particleSensor.setup();                     //Configure sensor with default settings
  particleSensor.setPulseAmplitudeRed(0x0A);  //Turn Red LED to low to indicate sensor is running
  particleSensor.setPulseAmplitudeGreen(0);   //Turn off Green LED
}

void loop() {
  long irValue = particleSensor.getIR();

  if (checkForBeat(irValue) == true) {
    //Calculate beatsPerMinute
    long delta = millis() - lastBeat;
    lastBeat = millis();
    beatsPerMinute = 60 / (delta / 1000.0);

    //Check if the BPM value is within a valid range
    if (beatsPerMinute < 255 && beatsPerMinute > 20) {
      rates[rateSpot++] = (byte)beatsPerMinute;
      rateSpot %= RATE_SIZE;

      //Take average of readings
      beatAvg = 0;
      for (byte x = 0; x < RATE_SIZE; x++)
        beatAvg += rates[x];
      beatAvg /= RATE_SIZE;
    }
  }

  // Print IR value, current BPM, and average BPM to Serial Monitor
  Serial.print("IR=");
  Serial.print(irValue);
  Serial.print(", BPM=");
  Serial.print(beatsPerMinute);
  Serial.print(", Avg BPM=");
  Serial.print(beatAvg);
  if (irValue < 50000) {
    Serial.print(" No finger?");
  }
  Serial.println();
}